(027)6160 3188 \ 6160 3588

Online Message

Social media

Building E 4-2, Huazhong Enterprise City, 16 Hankou North Avenue, Wuhan



Tel:(027)61503288 18995601588
Tel:(027)61603188 61603588
After sales:61603188-8028


Contact us


SIVACOII 8PT drawer type low voltage switchgear
Page view:

SIVACOII 8PT drawer type low voltage switchgear

I want to make an inquiry
Product Description
The SIVACON 8PT low-voltage switchgear is a new low-voltage switchgear designed by Siemens. It has circuit breaker technology, fixed-mount technology and drawer technology design. The SIVACIN 8PT produced by the company as a “licensed production partner” of Siemens is suitable for low-voltage distribution systems with AC 50HZ and rated working voltages of 690V and below. As a variety of power generation, transmission, distribution, power conversion and power consumption control equipment, can be widely used in industrial and mining enterprises, building hotels, municipal construction and other low-voltage power distribution systems.
The switchgear is fully compliant with the national standard GB7251 and the international standard IEC60439-I.
◆ SIVACON8PT drawer type switchgear with motor circuit and cable feed circuit has the best safety and applicability to provide high operational convenience.
◆With the wizard's withdrawing mechanism, it can be quickly and easily replaced and adjusted, so each module can be modified or changed, even if the compartment can be changed during operation.
◆ Standard modules that pass the form test have a high level of safety. The outlet circuit can be up to 250kW. Can be protected with fuses or circuit breakers. The degree of protection for the test position and the separation position is IP300. All extraction units have a standard operating interface. There is an isolation interval on the power supply side and the power supply side. The draw-out unit saves space and the minimum unit height is lOOmm. The cable connection compartment can be adjusted at the front or rear, depending on changing conditions, without the need to power down the entire cabinet.
◆The skeleton is made of 2.5mm high-quality steel plate with a hole with a modulus of 25mm. It can be expanded for various purposes and the cable can be connected above or below.
◆The enclosure protection grade is IP30, IP31, IP40, IP41, IP42, IP54.
◆Light weight, high mechanical strength and assembly precision, beautiful appearance.
◆High technical performance: The main parameters have reached the international advanced level.
  The main technical parameters
◆ rated working voltage to 690 (v)
◆ rated insulation voltage 1000 (v)
◆rated working current
Horizontal bus to 7400A
Vertical bus to 2800A
◆Rated short-time withstand current RMS (1s) / peak (kA) to lOOkA / to 250kA
Horizontal bus to 65kA/163kA
Vertical bus to 4000A
◆Switch rated current
Circuit breaker to 630A
Cable feed circuit IP30 to IP54
◆ cabinet protection grade
◆Outer size
Height: 2200mm, 2600mm
Width: 400, 600, 800, 1000, 1600mm
Deep: 600,800,1000,1200mm
Normal use environmental conditions
◆The ambient air temperature is not higher than +40 ° C, not lower than -5 ° C, and its average temperature is not higher than 350 ° C within 24 h
◆Installed indoors, the altitude does not exceed 2000 meters.
◆ Atmospheric conditions: Relative humidity is +40 at the highest temperature. C is not more than 50%, and a higher relative humidity is allowed at a lower temperature, for example, 90% at +20 ° C. However, in view of temperature changes, the influence of condensation may occur by chance.
◆The device is suitable for the transportation and storage process of the following temperature: between -25 ° C and 55 ° C, in a short time (not more than 24 h) up to +700 ° C, at these extreme temperatures, the device should not It is subject to any irreparable damage and can work normally under normal conditions.
◆The equipment is installed in a place free from explosion hazard, chemical corrosion and severe vibration.
◆ Exceeding the above conditions of use, when the user has special requirements, it can be specially negotiated with the manufacturer.
Internal structure
The basic structure of the cabinet is composed of fixed steel profiles connected to each other and can be divided into several compartments according to requirements, namely main bus room, electrical room, cable room and horizontal wiring compartment (for connection between cabinet and cabinet) wire). The skeleton profile has a M=25mm mounting hole and the outer casing is made of 2mm steel plate. Users can choose the surface treatment method (powder coating, painting or galvanizing) according to their needs.
Corresponding parameter set not found, please add it in property template of background
Previous article